Our Blogs

If you are a homeowner in Australia, it’s important to be aware of the average lifespan of your hot water system. Knowing when it’s time for a replacement can save you money in the long run. In this blog post, we will take a look at the average life expectancy and also provide some tips on how to prolong the life of your hot water system.

How long do hot water systems typically last before they need to be replaced?

The hot water system in your home is one of the most important appliances. It provides a consistent hot water supply for cooking, cleaning, and bathing. While hot water systems are built to last, they will eventually need to be replaced. Most hot water systems have a lifespan of around ten years. However, this can vary depending on the type of system and how well it is maintained. Suppose you suspect that your hot water system is nearing the end of its life. In that case, it’s important to contact a professional plumber for an inspection. With proper care and maintenance, you can extend the life of your hot water system and avoid costly repairs or replacements.

Factors that can affect how long a hot water system lasts

Several factors can affect how long a hot water system lasts. The type of system, the quality of the installation, the amount of use it gets, and the level of maintenance it receives are all important considerations. Additionally, hot water systems that are subject to extreme temperatures or hard water conditions may have a shorter lifespan. With proper installation and care, however, most hot water systems will provide years of reliable service. By understanding the factors affecting a hot water system’s lifespan, homeowners can be better prepared to ensure their investment lasts as long as possible.

Quality of Equipment and material

One of the most common reasons a hot water system needs to be replaced is that the water tank corrodes over time. This can happen even with regular maintenance, as the hot water itself can cause the tank to break down over time. When this happens, you’ll need to replace your hot water system. However, buying a better quality product may increase its lifespan by a matter of years. Look for a hot water system with a corrosion-resistant storage tank, such as one made of stainless steel. You may also want to consider products with a hot water system warranty. By taking these steps, you can help ensure that your hot water system lasts for as long as possible.

Type of water heater

A hot water system’s life span will be different based on the type of water heater being used. With proper maintenance, gas water heaters will typically last for about ten to twelve years. Electric water heaters have a longer lifespan and can last up to fifteen years. Continuous flow water heaters have a longer lifespan and typically last around fifteen to twenty years. The type of hot water system that is being used will play a big role in how long it will continue to function properly.

Wear and tear

The hot water system in your home is subject to a lot of wear and tear. Every time you turn on the hot water tap, the system has to work to heat up the water and deliver it to you. This puts strain on the heating element of the system, and over time this can lead to problems. The volume of usage is also a big factor in the lifespan of a hot water system. Suppose you have a large family or use hot water for many activities. In that case, your current water heaters will have to work as hard as commercial water heaters and, therefore, have a shorter lifespan.

Water quality

One factor that can significantly impact the lifespan of your hot water system is the quality of the water that passes through it. In some areas, the water quality is poorer than in others, and this can cause corrosion to occur on your tank much more quickly. This is often referred to as “hard water”.

What you can do to prolong the life of your hot water system

With proper care and regular maintenance, you can prolong the life of your hot water system and avoid needing a costly replacement. Here are a few tips to follow:

• Inspect your hot water system regularly for signs of leaks or corrosion. These can be indicative of bigger problems that, if left unaddressed, could lead to a premature failure of your system.
• Have your hot water system serviced by a professional. Preemptive hot water system maintenance will help ensure that it operates efficiently and identify any potential problems before they cause significant damage.
• Upgrade your hot water system to a more energy-efficient model when it is time for a replacement. This will save you money on your energy bills and help conserve resources.

Signs that it might be time to replace your hot water system

Generally, hot water systems should be replaced within the prescribed years. However, there are a few signs that your hot water system might be reaching the end of its lifespan. If you notice any of the following, it might be time to call the hot water experts and get a new hot water system installed:

• Your hot water system is old. The average life expectancy may vary depending on the type, brand, and make.
• You have to wait longer for hot water.
• The hot water isn’t as hot as it used to be, or
• you experience a rapid loss of water heat.
• You hear strange noises when you turn on the hot water tap.
  Your energy bills have gone up.
• There is rust in the tank or pipes.
• Discoloured water.
• Low hot water pressure but adequate pressure on the cold water tap.
• The hot water tank or the hot water unit is leaking.

These are just a few signs that your hot water system might be on its last legs. If you’re not sure whether or not you need a new hot water system, it’s always best to consult with a licensed plumber. They will be able to assess your situation and give you the best advice for moving forward.

Tips for choosing a new hot water system

When it comes to hot water systems, there are a few things to consider in order to choose the best one for your home. The first step is to determine the capacity you will need. This will be based on the number of people in your household and your typical hot water usage. For example, suppose you have a large family, and everyone takes multiple showers each day. In that case, you will need a system with a higher capacity than a smaller family that only uses hot water for cooking and washing dishes. Once you know the capacity you need, the next step is to decide on the type of hot water system that will best meet your needs. There are three main types of hot water systems: tankless, heat pump, and solar. Each has its own unique benefits, so it is important to do some research to figure out which one will work best for your home. Finally, be sure to consult with a qualified plumber before making your final decision. They can help you determine the size and type of system that will be best for your home and provide installation services.

Let us help you

At Rowson’s Plumbing Services, we understand the importance of hot water. That’s why we offer a comprehensive hot water system service, including servicing and maintenance, affordable repairs, water heater replacement, and more. We also sell hot water units, so you can be sure you’re getting the best possible product for your needs. Whether you’re having hot water issues or looking to upgrade your hot water system, we have a top-of-the-line hot water solution. Contact our expert plumbers today to learn more about what we can do for you.

So, you’re having trouble with your toilet tank not filling up after a flush? It’s quite common for homeowners to encounter this problem. There are many different reasons why the issue could arise. While none of them will necessarily break down or damage anything important (in fact, most can be easily resolved), it may help identify what is causing these problems so that we know how best to tackle fixing things right away! 

To find out how to troubleshoot and fix a slow filling toilet, read on.

Why Is the Toilet Tank Slow to Fill?

Generally, a toilet tank will refill in about a minute based on the pressure of water in your home. You may have a problem if it takes a long time to complete.

For the following reasons, you might be having a slow-filling toilet.

Low water pressure

Some elevated areas have low water pressure, and this may cause your toilet tank to fill slowly. Some homes opt for a pressure regulating pump to avoid insufficient water pressure issues.

Check your taps in all the rooms and see if the water flow is adequate. 

A problem with the water supply valve

A water supply valve is located just below the toilet tank, behind the toilet bowl, and is responsible for controlling the flow of water into the toilet tank. A partially closed valve or a malfunctioning valve may not regulate the flow of water correctly. Lastly, debris buildup can prevent water from flowing smoothly through the valve, reducing its filling capacity.

Tips for troubleshooting: Make sure your valve is completely open. Contact a licensed plumber for assistance if an open valve does not produce enough water to refill the tank.

A Waterlogged Float Ball

Water is regulated in the tank by a float ball. A waterlogged float ball prevents the tank from filling efficiently. Consequently, it can prevent enough water from entering the tank, or it can cause the water to refill at a slower rate than desired.

You can check the water level by removing the toilet tank lid. Your float ball could be waterlogged if it’s partially filled or doesn’t float near the top of the tank. If you need to replace the float ball, you just have to remove the old one and install the new one.

It should be noted that float balls are old toilet technology. In case this mechanism is in need of replacement, consider purchasing modern parts for your inner toilet.

Problems with the Fill Valve Tube

Fill valves are located at the end of vertical tubes inside the toilet tank. Fill valves are used to control water levels in tanks. Fill valves are susceptible to wearing down, blockageging, or shifting out of alignment over time. A toilet that cannot fill with water properly may be affected by any of these negative factors.

After you’ve determined that the problem isn’t with a waterlogged float ball or with the water supply valve, it’s time to investigate the fill valve. Make sure the valve is not worn out or improperly positioned inside the tank. It’s normally mounted on the left side of the tank, with the tailpiece extending through the bottom, where it’s connected to the shut-off valve and supply tube.

How To Fix Fixing a Slowly Filling Toilet

After learning what the cause of a slow toilet tank fill will be, here are some steps you can take to fix the issue.

Call Your Neighbours

Ask your neighbours if they are experiencing insufficient water pressure. If they are, then it’s an issue with the municipal water line, and all you can do is report the problem. If not, then call a plumber; you may have a bigger issue than just low water pressure and a slow filling toilet tank.

Turn On the Water Supply Valve

More often than not, the water supply valve is only partially open is the main culprit. Make sure the valve is fully open.

Adjust the Fill Valve

Follow these steps to adjust the toilet fill valve:

• Locate the fill valve on the left side of the tank after removing the tank lid.
• Fill valves need to be secured and evenly attached to their tubes.
• The adjustment screw on an older toilet can be loosened and the fill valve opened with a flathead screwdriver. We suggest calling a licensed plumber for old models.
• With a hand, turn the fitting of a modern toilet to increase the amount of water in the tank.
• For new or old toilets, the water level should be about an inch below the top of the overflow tube.
• Once the toilet is flushed, ensure the tank has been filled at the right rate and with the proper amount of water.

The Fill Valve Needs Cleaning 

Does the fill valve seem to have mineral deposits and gunk? Cleaning it is as follows:

• Call an experienced plumber. The fill valve is a tricky component to handle, and without proper training and experience, you may end up with more problems than when you started.
• Cleaning the fill valve involves removing screws, fill caps, washers and gaskets. Mishandling these might mean that you need to replace the whole mechanism.
• Not to mention the cleaning, scrubbing and putting it back in place correctly. It’s best to not do it yourself and call the professionals.

Replace or Fix a Waterlogged Float Ball

• Make sure the float ball is not mounted too low on the toilet float arm. It’s easy to increase water flow by bending the arm slightly upward, so the ball does not fall to the bottom of the tank.
• However, if this still does not work, you may need to install a new float ball or consult your local plumber about replacing the old-style mechanism with a newer one.

Fix a Valve Tube Problem

The valve tube must be cleaned of debris to fix a blocked one. But this requires removing and replacing hardware that would require gentleness and technique. Mishandling such mechanisms may end up in damaged washers. We suggest you call a plumber.

When to Call a Plumber?

The best time to call a plumber is if you understand your limits and the limitations and dangers of DIY solutions. Call a plumber if you notice a slow filling toilet tank during normal business hours. You’d be surprised how kind a plumber could be and walk you through the actual steps in troubleshooting the toilet tank problem. A plumber would know better and have experienced more of the same situations, and could come up with the correct solution for common issues. So, don’t hesitate to call the best local plumbers in Perth at Rowson’s Plumbing Services.

Homeowners may find themselves in a frustrating situation when their water pressure in the kitchen suddenly drops, and the sink is piled high with dirty dishes. Decreased water pressure can make a fifteen-minute wash job into an hour, and it is certainly annoying. There are a variety of factors that frequently contribute to this problem! We will go over a variety of water pressure issues, ranging from simple fixes to those that necessitate the services of a professional plumber.

Water Pressure Problems in The Kitchen 

There is indeed a wide range of factors that can contribute to low water pressure within the kitchen. Here are a few examples of common causes:

Broken Water Supply Lines

One of the most prevalent reasons for the low water pressure in your residence is an issue with a municipal water supply line, which can affect many areas at once. 

When this screws up, you’ll notice similar issues in the other fixtures that use or rely on it, such as bathroom taps, showers, and water appliances, among other things.

Clogged Aerators

The problem is typically caused by mineral deposits as well as debris that accumulates when water passes through a taps aerator, according to the manufacturer. Due to the accumulation of scale on its way down from the source to the tap, the pressure in your home’s pipes will gradually decrease over time as it travels down from the source to the tap.

Cartridge Clogs

The cartridge is a component of kitchen taps that needs to be replaced when it becomes blocked. If you notice that your water flow has decreased, then this could be an issue with the unit’s system and not just dirt in between gaps, as many people think!

Leaks

If a pipe supplying water to your fixture has sprung an ugly leak, then you’re probably noticing some of the signs. This issue can cause damage in homes with low pressure and lead to problems like flooding or expensive repairs down the line if left unchecked for too long!

Errors Related to Shutoff Valves

You will find supply valves for each sink at your home, which will cut off the flow of water to that particular fixture. Usually, they’re under the sink or behind it. Low water pressure in kitchen fixtures often happens when the shutoff valves malfunction or are accidentally moved into a more closed position.

How to Determine the Cause of Low Water Pressure in Kitchen Fixtures

Water pressure can be restored to normal in kitchen taps by determining the source of the low pressure. A little elbow grease and the proper knowledge can help homeowners decide whether or not they can fix the problem:

Each source of water should be turned on individually. The problem is isolated to your kitchen if all other areas have adequate pressure.

When you have low hot water pressure but adequate cold water pressure in your home, you likely have a problem with your water heater. You should contact your local plumber about this issue.

Make sure the plumbing around and under your kitchen sink is in good working order. Stuffing random things under the sink might have nudged your water valves.

The cause of low water pressure in your kitchen tap might be a water leak if you see standing or dripping water. This problem can be solved by calling a plumbing service.

Are your homes’ hot and cold water pressures low in all rooms? Give your neighbour a call right now. Water pressure issues are likely to originate from your municipal water supply. If this is the case, you should contact your water provider to report the problem. They might be flushing hydrants or repairing water mains in your area.

Easy Fixes for Minor Kitchen Water Pressure Issues

After completing this checklist and still not seeing a satisfactory result, try these DIY fixes.

Check the Water Supply Valve

Check under the sink for the water supply valve. Just give that thing a few turns and check if the water pressure issue is solved. Righty tighty; lefty loosey. Make sure that the valve is set to fully open. And to avoid the valve being closed accidentally, stop shoving random things under the sink.

You Should Check Your Aerator

There is a mesh screen over the water outlet of your tabs, which serves as an aerator. An aerator screen collects minerals and debris in your pipes. Air is also introduced into the water stream, which helps reduce water consumption. Water aerators become blocked with hard water build-up if you have especially hard water, leading to low water pressure in kitchen fixtures. You can quickly fix your aerator by cleaning it.

Check Your Tabs Cartridge

In your tabs, the cartridge sits deeper than the aerator and has a hole through which water passes. Hard water build-up causes these cartridges to blockage or block, resulting in low water pressure in kitchen taps. Most of the time, they just need to be cleaned. Again, this can be done relatively quickly.

Special Cases

There are a few exceptional cases where the elevation of the area causes low water pressure at certain times. This is due mainly to the number of households using their taps at the same time, leaving the houses in high elevation areas with low water pressure. Most homes opt for electric pumps or water pressure booster pumps to have steady water pressure.

Rowson’s Plumbing Services Can Fix Low Water Pressure in Kitchen Taps 

Is the problem still not resolved? Have no time to handle it? Rowson’s Plumbing services can provide you with a licensed plumber. Some causes of low water pressure should be left to a professional plumber. Leaks in your water pipe are not something to DIY. You can rely on us for quick service and expert plumbers who can locate the problem at the source and get your tabs working again as soon as possible!

Water heater repair and installation, water pump repair and maintenance services, leaking pipes, water filtration systems, toilet problems, tabs replacements, blocked sinks, and more are handled by our plumbing professionals. Don’t hesitate to call.

So you’re not alone if you notice water pooling at the base of your toilet bowl. It’s something that plumbers see all the time, and it can be caused by a number of things, from tank leaks to loose bolts. One thing is for sure, it’s an issue that needs to be dealt with promptly, so you don’t have to deal with any significant problems down the line. In this blog post, we’ll go over some common causes and offer solutions to help keep your plumbing intact during these cold winter months. 

Common Causes of Leaks in The Toilet Base Include:

All toilets may leak from their bases for a variety of reasons.

Loose Tee-Bolts.

The two bolts that hold your toilet’s base to the ground are called tee bolts. These bolts are likely to loosen, causing the toilet to rock, resulting in a broken seal. When your tee bolts are very loose, drain water may leak out each time you flush the toilet.

Wax Rings Need to Be Replaced.

If the toilet is loose, the wax ring seal usually needs to be replaced with a new wax ring.

In addition to damage from age, wax rings may require replacement because they have become rigid and inflexible over time. In other words, it no longer has a watertight seal. The result is water seeping through the base.

Cracked Toilet.

This may be caused by putting more than just your body weight on the toilet; impact; or just plain old age. You would notice dirty water and excess water on the bathroom floor every time you flush. Another indicator is that the water level in the toilet is lower than usual. The biggest giveaway of a cracked toilet is the visible crack.

An Unsecured Water Supply Line Exists.

There will be a constant water leak if there is a loose water supply line, rather than just when you flush. You should make sure the rubber seal and the nut on the connection of the supply line to the tank have a tight seal.

A Large Amount of Water Is Condensing on The Toilet.

Most toilet tanks and bowls contain cold water, as do the porcelain bowls. When your room is humid, water will drip from the porcelain on the bowl, causing water to pool at the base of your toilet. 

Once you’ve discovered the actual toilet leak’s source, we will know what to do next.

When Should I Call a Plumber?

It’s best to call a professional plumber for anything that concerns the toilet. The toilet manages human waste and is the only connection to the home and sewer pipes. It’s best to leave that to trained professionals who know how to handle black water. 

What the Plumbers Are Trained to Do:

In replacing the wax ring seal on a toilet, the plumber would need to shut off the water supply for the toilet tank. To minimize the wetness of the workspace, the tank would be emptied by flushing the remaining contents of the tank and removing the tank lid to make sure it’s empty.

The water supply tube should be disconnected and the tee bolt nuts exposed and removed. The plumber will carefully rock the toilet back and forth and break the seal and slowly remove the toilet and avoid potential damage. With a putty knife, the old wax gasket will also be removed from the bottom of the toilet and from the flange in the floor.

The floor flanges would need to be checked if they needed to be replaced entirely. 

After the wax seal has been replaced, the toilet needs to be put back in place securely and tightly.

In the event of a cracked toilet, it would more or less constitute emergency plumbing issues and would need to be addressed immediately. It’s not just a leaky toilet base; it would be best not to put any weight on that cracked toilet. Call a plumbing service and tell them about the cracked toilet. Most plumbers would hook you up with the best toilet models to replace the cracked toilet. Not to mention the instalment of such a fixture.

How to Prevent Future Leaks

Most toilet leaks are caused by wear and tear. Over the course of the toilet’s life of service, wax seals will eventually break, water supply gaskets will leak condensation is natural. The only thing we can actively avoid is putting too much weight on the toilet. The wax seal and the bowl are designed to support body weight at certain angles. Using a toilet for other activities that they weren’t meant for would undoubtedly cause damage. 

Regular inspection of your plumbing, including the toilet, would make sure that any plumbing issues are discovered and dealt with before getting too big and expensive. Call the courteous plumbers in Perth at Rowson’s Plumbing Services and ask about regular plumbing checks.

What makes my toilet smell so bad? There is a strong probability you have cleaned and disinfected, but the odour just isn’t subsiding. Toilet odours are the bane of every homeowner. In addition to being unpleasant for you and your guests, it is downright embarrassing. Using air fresheners and candles to catch the smell of a stinky toilet might be tempting, but it doesn’t solve the issue. You can actually introduce toxic air into your home by doing this. This decreases the air quality in your home.

In the event you have thoroughly cleaned your toilet and the area still smells, there are several possible causes.

The following are some common reasons why your clean toilet smells:

Broken or Missing Toilet Seals

Any urine or water that has leaked under the toilet can encourage bacteria growth if there is no caulk sealing the area. By itself, this can cause odour problems in your bathroom. You may be able to seal the nasty smell into the floor by caulking around the toilet base, but removing the toilet and cleaning underneath it first is a good idea. A professional plumber should remove your toilet if you are uncomfortable doing so.

Incorrectly installed or blocked vent pipes.

The main indication that there may be a problem with the vent pipes is a toilet that looks and functions fine while emitting a foul smell in the bath area despite cleaning. Make sure the vent pipe on your roof releases sewer gases properly. Leaves and debris will prevent the gases from escaping, leading to a stinky toilet. Check to see if clearing the pipe of debris helps. It may be impossible to determine if a vent pipe has been severed or installed incorrectly by visual assessment. In this case, it’s best to contact a plumber for a professional diagnosis and repair.

Broken or Loose Toilet Bolts

A loose bolt or broken flange on your toilet will cause it to rock or wobble. In order to test the toilet, tighten the bolts that fasten it to the floor. If this does not resolve the sewage smell, it could be an issue with the wax ring or flange between the toilet and the waste pipe that should create an air-and water-tight seal. It is a good idea to call a plumber to examine these components if you are unfamiliar with them.

Invasion of Bacteria from The Sewer Into a Toilet Bowl

Somehow, microorganisms from the sewer may find their way into the toilet, where they will then multiply. Bacteria thrive in hot, humid conditions during the summer, which leads to this problem.

You can make quick work of cleaning up these unwanted visitors by pouring bleach into the toilet tank’s flush valve or overflow pipe. Flushing of the toilet will release the bleach, which will eliminate the bacteria and unpleasant smell.

The Toilet Tank Is Dirty

Cleaning your toilet bowl thoroughly does not ensure that your toilet tank is clean. Even when the toilet bowl is clean, your toilet’s tank can absorb the smell of urine and sewage. 

You can clean a dirty toilet tank in the same way you clean a dirty toilet bowl. It only takes you a few minutes to use a toilet brush and some white vinegar to scrub the tank walls with. To remove the vinegar from your toilet tank, flush your toilet several times after letting it sit for a few minutes. You should be able to get rid of the bad smell immediately.

Having a Clogged Toilet Drain

Even if the toilet is flushing normally, it might have a minor blockage. If your toilet is blocked even slightly, you can smell sewer gas. 

If you suspect your smelly toilet may be the result of a blocked drain, use a drain snake to clear any minor obstructions from the drain, and get rid of any bad bathroom odours.

Replace a Damaged Toilet if It Is Damaged

If you have determined the problem is not the vent pipe, bolts, flange, or seal, you may have a damaged toilet or a more serious plumbing problem that requires an experienced plumber. Have you been scratching your head and holding your nose at the same time while trying to diagnose the problem? It’s time to call on a trusted professional plumber for toilet repair or replacement.

Speak To A Licensed Plumber Today

It is still best to call a plumber with any plumbing issue you encounter. You may be capable, but professional plumbers have more experience. Call the best-licensed plumbers in Perth to fix the issue and give you peace of mind. You can trust Rowson’s Plumbing Services to deliver the best service possible. Give us a call today and find out how our team of professionals will treat you with respect, follow through on commitments, and maintain high standards in every aspect of your plumbing needs!

A home that is older has many advantages. The problem is that some buyers experience buyer’s remorse after acquiring a property that needs thousands of dollars in repairs. It is important to ask about these common plumbing problems before you purchase a home in Perth if you want to prevent the need for plumbing services.

Plumbing-How Does It Affect Us? 

A home that is older requires attention to a lot of details. There is a possibility that the roof, electrical system, and HVAC system are near their end. Does worrying about the plumbing really make sense, given everything else you have to worry about?

I would say yes. Approximately 15% of a home’s value is the plumbing system. So, the price should be reflected in the plumbing condition of the home. In the case where the plumbing is older than 25 years and poorly maintained, your offer should be reduced accordingly.

It will be costly to repair a major plumbing issue. Depending on the severity of the issue, you may have to replace the pipes. Working with a plumber who offers 24-hour service can save you the hassle of an unexpected repair. While a home inspector might probe the plumbing system, he or she is not an expert. There might not be signs of defective pipes detected by the expert.

It’s important to hire a plumber in addition to a home inspector. Ask them to examine the plumbing in the home and learn more about it. You should ask a few common questions to better understand how much work your system will need.

Ask Your Plumber These Questions.

A qualified plumber knows how to diagnose plumbing problems. When dealing with an older home, ask these questions to ensure that it won’t be a money pit for plumbing repairs.

Did the Previous Owners Perform Diy Fixes? 

The current owners can answer this question, but there is no guarantee that they will be honest. Some homeowners attempt to do plumbing repairs themselves in an attempt to save money. Unfortunately, future owners will have to deal with this. A DIY repair is typically performed improperly. Additionally, they might not always be up to building code, causing you trouble and costly issues.

A plumber might notice some unusual details as they inspect your system. These details may indicate that DIY plumbing work was performed. It may be necessary to invest in your plumbing to bring it up to code and ensure that it is working properly.

Does the Hot Water System Work? 

A water heater will not last forever, just like most household appliances. As a matter of fact, its lifespan is only eight to twelve years. You will need to spend money on a replacement heater, but keeping an outdated heater will cost you more.

This can be explained by two factors. In the first place, old heaters require frequent repairs. You will begin to shell out money for repairs as you get to know your plumber by name. In addition, these units aren’t energy-efficient. Due to your old water heater, you could have a high energy bill.

New water heaters can lower your utility bills and prevent repairs. If your plumber has any recommendations for a new, more efficient heater, ask him what he thinks of the existing heater. Don’t overlook the benefits of tankless water heaters or hybrids.

Do I Need to Replace the Toilet and Other Appliances? 

The problem with your hot water isn’t the only thing your plumber should address. You should have a plumber inspect any other appliances that rely on water. Included in this are dishwashers and toilets.

You may have an inefficient toilet or dishwasher, just like with your water heater. In the long run, you might end up with a home that has high energy bills if they aren’t replaced. Aside from the obvious benefits of having these items inspected, there is another benefit. An inspection by your plumber may reveal a serious leak in your plumbing. You may be able to avoid the extra costs by being thorough once again when buying a home.

Is It Made of Copper, PVC, Iron, or Galvanized Pipes?

After 1930, most houses had copper pipes. However, older houses don’t always have copper pipes. The danger of lead was unknown decades ago. Copper pipes with lead solder were common in some homes. Unfortunately, lead causes kidney damage and brain damage as well. The copper pipes in your prospective home will need to be replaced if they contain copper.

Your pipes need to be replaced, and it is not an inexpensive fix. However, it increases the value of your new home. The most important thing is that your family will be safer from toxic water when your pipes are replaced.

Is There a Leak in The Sewer Pipes?

A broken sewer line is one of the biggest plumbing headaches. It is difficult to access these lines, and major repairs may be labour-intensive. In older homes, the sewer lines tend to be in bad shape, so make sure you ask about yours.

Several issues may cause problems in the future. Over time, pipes are susceptible to eroding and must be replaced. Leaking joints are another common problem. You may even encounter problems with your plumbing caused by tree roots that grow into sewer lines.

It is more than inconvenient to experience sewer line trouble. You’re also at risk of health problems. Whenever a sewer line breaks, you should call a 24-hour plumbing service provider. If you want to avoid that situation, you can have a plumber inspect your lines first.

How Is the Water Pressure in The Area?

Ask around the neighbourhood if there are any low water pressure issues. A telltale sign would be water pumps for every house. If that is the case, have a plumber check the condition of the pump and calculate the expenses if there are any.

The Plumber and Building Inspector

Have a local plumber come along with the building inspector before you agree to the price and sign that contract of sale. Call the best plumbers in Perth at Rowson’s Plumbing Services to check on that property’s plumbing system. Ask for a quote on all the needed repairs and replacements needed. This can help you negotiate the potential cost of the property.